Browse all practice questions for the Michigan Journeyman Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Michigan Journeyman Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • What color insulation typically indicates a ground wire?
  • When encountering rock during the installation of a ground rod, at what maximum angle should the rod be driven?
  • What is a key consideration when designing temporary wiring installations?
  • Why is it important to keep electrical circuits balanced?
  • Which type of protection is required for personnel for all temporary wiring installations?
  • What is the minimum length requirement for ground rods?
  • In Michigan, which type of license must an electrician have to work independently?
  • What does a circuit need to be considered a "correctly grounded" system?
  • What is the smallest size conductor allowed for a ground ring?
  • What should be the minimum clearance for overhead service drops?
  • A feeder in a single-family dwelling supplies a load of 75 A of electrical space heating and 25 A of air conditioning. The required capacity of the feeder is _____ amps?
  • What is a three-phase system?
  • For what purpose are branch circuits used in an elevator system?
  • How is the term "load center" defined in electrical work?
  • Can type insulated conductors be used in direct burial applications?
  • What type of branch circuits shall furnaces be supplied by?
  • Under what condition does a dishwasher not require GFCI protection?
  • What does NEC stand for?
  • What is the minimum size ungrounded service entrance conductor for a 120-240 V single phase 200 amp service in a commercial building?
  • A single man motor operated appliance of 134 A shall have overcurrent protection not to exceed what percentage of the appliance rating?
  • Which electrical device is used to provide overload protection?
  • What is the minimum size ground wire for a 200 amp service?
  • Work installed by an electrical contractor can be concealed after what condition is met?
  • What is the purpose of circuit breakers in a panel?
  • What is the purpose of a junction box?
  • What standard defines the acceptable distances between electrical equipment and likely sources of water?
  • What is the function of an arc fault circuit interrupter (AFCI)?
  • What is the main benefit of conduit installations?
  • When are two ground rods required for a residential service?
  • Auxiliary gutters shall not contain more than how many current carrying conductors without derating?
  • What voltage does a standard household circuit usually operate at?
  • How can the direction of rotation of a three-phase motor be reversed?
  • What is photometric analysis used for in lighting design?
  • What kind of circuit is typically used for residential lighting?
  • Which component is essential when ensuring the safety of elevated work locations?
  • What is the minimum distance required when installing two ground rods?
  • What is the minimum distance a metal fence must be bonded when installed near a pool?
  • What does the term "ampacity" refer to?
  • An electrical device which consists of a frame, plunger, and coil to create a push or pull action is called what?
  • What measure can reduce the risk of electrical shock in wet environments?
  • How frequently should smoke alarms be tested?
  • What type of wiring is typically used for lighting fixtures?
  • What is the term for the maximum current that a conductor can safely carry?
  • What is the minimum conductor size for a circuit with six conductors connected to a 75° C rated circuit breaker, each carrying a 70 amp load?
  • What is the purpose of a load center?
  • Why are lighting outlets necessary in habitable rooms?
  • A light fixture that weighs more than what weight must be supported independently of the junction box?
  • What is the required minimum height for a service drop above residential property?
  • What is the purpose of stranded conductors?
  • What is the purpose of an electrical service disconnect?
  • Which type of cable is not permitted for service entrance conductors?
  • For non-metallic conduits, what is the safe minimum burial depth?
  • What is the minimum height for outlet boxes above the finished floor in dwellings?
  • In a residential installation, which of the following is an acceptable size for a service entrance conductor?
  • Branch circuits larger than ______ amps shall supply only non-lighting loads.
  • What is the minimum size of a service entrance cable for a 200-amp service?
  • What is a GFCI protected circuit required for in bathrooms?
  • The maximum number of switches permitted to disconnect a service is ______?
  • What is an essential step to take before performing maintenance on electrical equipment?
  • What does the NESC stand for in relation to electrical work?
  • What is the primary purpose of using Schedule 80 PVC in electrical installations?
  • How far must a receptacle for laundry equipment be located from the intended location?
  • What is the main purpose of the National Electrical Code (NEC)?
  • An AC general use snap switch used to control a motor load shall not exceed what percentage of the amp being read of the switch's rated voltage?
  • What is the maximum number of conductors allowed in a conduit without derating?
  • What is a common application for branch circuits in residential wiring?
  • What safety equipment is essential when working on electrical installations?
  • What is the minimum voltage rating for communication cable?
  • What does “junction box fill” refer to?
  • The code requires a blank cubic inches of free space for each number 10 wire in an outlet box.
  • What is the maximum allowable voltage for low-voltage lighting systems?
  • What is the term for a screw connecting the neutral bar to the service equipment enclosure?
  • How should electrical wire be properly secured?
  • What should be the minimum rating of a receptacle for use near a rooftop air conditioner?
  • What is a common use for a 3-way switch?
  • Short sections of Farris metal raceway used for physical protection of the grounding electrode conductor shall be bonded at both ends to the ______.
  • What is the formula for calculating electrical power?
  • A 15 or 20 amp receptacle must be located within how many feet of a rooftop air conditioner?
  • What is the maximum distance between supports for 1 inch rigid nonmetallic conduit?
  • What does the abbreviation "THHN" stand for in electrical wire types?
  • What is a typical use for low-voltage residential wiring?
  • When should circuit breakers be tested for functionality?
  • What is a common safety feature added to electrical installations to protect against ground faults?
  • What does the term "load calculation" refer to in electrical work?
  • What is an appropriate action when working in a potentially hazardous location?
  • How can you differentiate between a single-pole and three-way switch?
  • What does GFCI stand for in electrical safety?
  • What safety measure should be taken when working on circuits?
  • What is the minimum depth required for underground conduit installations?
  • How many volts are typically present in a residential electrical outlet?
  • What type of conduit should be used for direct burial cable emerging from the ground when it is subject to physical damage?
  • How many campers does a 208 V, three-phase heater that draws 3598 W support?
  • What is the maximum allowable voltage drop in a branch circuit?
  • When is a permit required for electrical work?
  • What does balanced electrical circuits help to ensure?
  • What is a primary function of branch circuits in electrical systems?
  • How many hours in advance must the inspection authority be notified before an inspection?
  • What is the primary function of a circuit tester?
  • Which type of conductor is preferred for ease of installation in complex wiring situations?
  • What is the minimum working space required in front of an electrical panel?
  • What type of lamp holders are required for fixed lighting units on a 30 amp branch circuit?
  • What type of current does a transformer typically handle?
  • What is the typical voltage drop limit for branch circuits?
  • What is the purpose of a junction box?
  • What is the primary role of a Journeyman Electrician?
  • How does a capacitor work in electrical systems?
  • What is a thermal overload relay?
  • What does the National Electrical Code (NEC) say about lighting in habitable rooms?
  • What is the function of a transformer?
  • What is the color code for a standard hot wire in residential wiring?
  • What risk does unbalanced electrical circuits pose?
  • What does the term “de-rating” refer to in electrical wiring?
  • What is the maximum allowable temperature for conductors rated at 60 degrees Celsius?
  • Which type of receptacle may be included on a small appliance branch circuit?
  • In an elevator system, which of the following is NOT typically considered when designing electrical circuits?
  • In which scenarios would a circuit breaker be necessary?
  • Which voltage is standard for most residential lighting in Michigan?
  • What is the main advantage of using LED lighting?
  • What is the minimum height for service conductors above a residential driveway?
  • The maximum number of number 6 AWG THW conductors allowed in a 1 inch PVC schedule 40 conduit is _____?
  • Receptacle outlets that are in or on the floor cannot be counted as required receptacles unless they are within how many inches of the wall?
  • For what situation would you use a step-down transformer?
  • What is the minimum service capacity required for a one-family dwelling?
  • What is the purpose of a load calculation in electrical systems?
  • What does "bonding" mean in electrical systems?
  • How should wiring for home entertainment systems be installed?
  • What is the primary function of a surge protector?
  • What is the minimum width of working space at a service panel?
  • What must be done when installing an electrical panel?
  • Direct burial cables rated above what voltage must be shielded?
  • In residential wiring, what purpose does a circuit breaker serve?
  • What type of raceways are required for DC photovoltaic source or output current inside a building?
  • What is the minimum number of hours of classroom instruction required for a Michigan Journeyman license?
  • What does NEC stand for?
  • What is a primary reason for using personal protective equipment (PPE) when working with electrical systems?
  • How can you identify a faulty circuit breaker?
  • What should be done if a conductor is damaged?
  • In a 1-inch conduit with three number 10 TW circuits, what is the maximum capacity of each phase conductor?
  • Where can the ratio of journeyman or master electricians to apprentice electricians in Michigan be found?
  • What does proper grounding help prevent?
  • What is the purpose of occupancy sensors in lighting fixtures?
  • If a comb rated at 4750 W, 208 V 3 phase draws how many amps?
  • M I cable shall be secured within what distance of a panel?
  • What is the primary purpose of a bushing in electrical installations?
  • What electrical issue is commonly treated with the installation of a surge protector?
  • What is the minimum height of a junction box for a 124 wet niche fixture above the ground?
  • What is the minimum height requirement for the coupling means of electrical vehicle supply equipment outdoors?
  • What is generally the ideal location for electrical outlets in homes?
  • What are branch circuits primarily responsible for?
  • Which component is essential for protecting against overloads in a circuit?
  • What is the main purpose of grounding in electrical systems?
  • What must be done before beginning any electrical work?
  • Which of the following is NOT an accepted method for securing electrical wire?
  • How far must thermal insulation be installed from recessed lighting fixtures?
  • Which material is commonly frowned upon for modern wiring due to safety concerns?
  • What does a white wire typically indicate in residential wiring?
  • What is a common reason for an electrical shock?
  • How can you ensure an electrical circuit is not energized before working on it?
  • When running insulated conductors that enter a box, which gauge creates a requirement for additional protection?
  • Which of the following is an acceptable way to protect electrical wires?
  • What should be used for an effective personal safety measure with temporary wiring?
  • What is the maximum distance an outlet can be from a kitchen sink?
  • A GFCI protected receptacle for a pump motor may be installed on which side of the dwelling unit?
  • What factor affects the ampacity of conductors when de-rating?
  • What is the minimum amp rating required for a service disconnect in a one-family dwelling unit?
  • General purpose receptacles are prohibited from being installed on which of the following?
  • What is the minimum size of rigid metal conduit for a commercial service rated at 150 A, 120/240 V single-phase using THWN wire?
  • What is a non-metallic sheathed cable commonly referred to as?
  • What is the NEC's requirement for lighting outlets in habitable rooms?
  • What does the abbreviation "SWD" mean in lighting fixtures?
  • When is it acceptable to use a non-metallic sheathed cable?
  • What material should be used to install the feed to the wet niche fixture?
  • In Michigan, what is the licensing authority for electricians?
  • How often should electrical equipment be inspected?
  • What is the function of a relay?
  • The impedance of NM cables is based on the blank degree column of table 310.15 B 16.
  • Which organization is responsible for enforcing the National Electrical Code?
  • What is the typical frequency of electrical systems in the U.S.?
  • What is the typical size of service entry conductors for a residential home?
  • What is considered an acceptable voltage drop for feeders and branch circuits?
  • Which regulation mandates that all electrical installations comply with safety measures?
  • What is the volt-ampere rating of a device that consumes 14.5 A on a 240 V circuit?
  • What safety precautions should be taken when working with live circuits?
  • How is wire gauge determined?
  • What must be installed within 10 feet of an above-ground pool?
  • Which type of circuit would most likely use a GFCI outlet?
  • What is the minimum vertical clearance for service drop conductors above a pedestrian sidewalk?
  • What is the purpose of a circuit breaker?
  • What does LARA stand for in Michigan's electrical licensing context?
  • What is a splice box used for?
  • What is the key difference between series and parallel circuits?
  • Which factor should be considered when selecting electrical cables?
  • What is the minimum amperage requirement for a power receptacle?
  • Which of the following is a typical use for a GFCI?
  • What should be installed in residential garages to meet safety standards?
  • What factor limits the operation of a high impedance grounded system?
  • Which of the following is true regarding circuit continuity?
  • What type of wire is required for outdoor installations?
  • What is the minimum size for an accessible hand hole in a metal light pole?
  • The impassivity of a number 6 AWG copper THHN conductor terminated in a switchboard rated at 75° C is how many amps?
  • How many days must an apprentice electrician register with the state of Michigan after initial employment?
  • What is the role of a panelboard?
  • What precaution should be taken when working on live circuits?
  • What does a watt-hour meter measure?
  • What is the purpose of electrical bonding?
  • A minimum size conductor that may be installed in parallel is ______ AWG?
  • What is the function of a Ground Fault Circuit Interrupter (GFCI)?
  • What is an electrical receptacle?
  • In Michigan, what is the maximum allowable load on a 15 amp circuit?
  • How many branch circuits are required for car lighting, ventilation, and heating per elevator car?
  • What does an ohmmeter measure?
  • When are fuses typically used in electrical systems?
  • Which of the following is an effect of outdated wiring?
  • What type of boxes should be used in the floor for installations?
  • What type of conduit should be avoided when installing service entrance conductors?
  • What size wire gauge requires protection by a bushing when entering a box?
  • What is the primary code used for electrical installations in Michigan?
  • What is a transformer used for in electrical circuits?
  • What type of grounding system is typically used for residential properties?
  • What is the standard voltage level for most residential electrical systems in the United States?
  • In a non-metallic box not larger than 2 1/4" x 4", cable clamps are not needed if the NM cable is stapled within what distance of the box?
  • What is the minimum distance underwater light fixtures must be installed below the water level?
  • What is the minimum vertical clearance for overhead power lines above streets?
  • What is the maximum ampacity allowed for Edison base fuses?
  • Where fuses are used for motor overload protection, a fuse shall be inserted in each ungrounded conductor and also in the grounded conductor if the supply system is ______ A/C with one conductor grounded.
  • Where shall disconnecting means be provided on a supply side of all carriage fuses?
  • At what minimum height must the coupling means of electrical vehicle supply equipment be stored indoors?
  • How many inches of thermal expansion occur for 100 feet of rigid nonmetallic conduit due to temperature changes between -15°F to 105°F?
  • Which type of conduit is commonly used for outdoor installations?
  • What is the function of a circuit breaker in an electrical system?
  • What is the primary purpose of branch circuits in electrical systems?
  • What are the minimum dimensions for a concrete encased steel reinforced base electrode?
  • What is the required length for the cord of a garbage disposal when installed with a cord and attachment plug?
  • A high impedance grounded system is limited to systems operating at what voltage or above?
  • Conductor fill of a conduit nipple 24 inches or less in length shall not exceed what percentage?
  • What type of meter measures electrical energy consumption?
  • How do you determine the size of a wire needed for a specific circuit?
  • What is the purpose of a ground fault circuit interrupter (GFCI)?
  • Where should round boxes not be used?
  • What does NEC Article 250 cover?
  • What is the required length of a ground ring in direct contact with the earth when installing around a building?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy